Readers ask: What Is Typical Width Of Whitetail Deer Buck Rack If Outside The Ears In Wisconsin?

How wide is a Bucks ears?

The average buck, with his ears in an alert position, has an ear tip-to-tip spread of 16 inches. His ears will measures six inches from the base to the tip. The circumference of his eye is four inches, and from the center of the eye to the end of his nose should measure about eight inches.

How wide is a whitetail buck?

They have a total length of between 60 to 75 inches and an average weight of about 150 pounds. It depends on where you are as the size varies. A big Midwestern whitetail averages 18″ but can be only 14″ in many eastern states. Mule deer can go all the way to 24 inches.

How do you judge deer antler width?

Estimating Spread By using the Ear tip-to-tip reference measurement of 13-15 inches, you can quickly gather if a buck’s spread is an inch or two inside or wider than his ears. For bucks that have a spread that far exceeds his ears, simply reference the ear base to tip measurement of 7-8 inches.

You might be interested:  Question: How Long Does The South Texas Whitetail Deer Rut Last?

How do you measure outside antler spread?

Measuring Spread. Measure the tip-to-tip spread with your measuring tape. This is the distance between the tip of the right antler and the tip of the left antler. Take the measurement from the front of the antlers.

What is a good score for a whitetail buck?

A two to four inch brow tine is fairly typical. Five to six inches is excellent. The second point (called the G-2) is another key area in determining a buck’s score. Good bucks will have at least seven or eight inch second points.

How big is a 150 class buck?

This measurement is around 7-8 inches. After you have referenced your initial measurements you will be ready to start field scoring the buck. Take a look at the picture above to memorize the reference points.

What is considered a big whitetail buck?

Some score as low as 126 inches while others score in excess of 162 inches. For the hunter that hasn’t been in the presence of a 125 inch Pope and Young Deer, it may take only a 125 inch deer to be a trophy. For the guy that thinks a whitetail buck must score 170 inches or better to be worthy of harvest then so be it.

How big is a 140 class buck?

This measurement is around 7-8 inches. After you have referenced your initial measurements you will be ready to start field scoring the buck. Take a look at the picture above to memorize the reference points.

What state produces the most Boone and Crockett bucks?

Boone and Crockett’s Top Whitetail States

  • #1 – Wisconsin. Wisconsin is the #1 ranked state with 1,822 total entries and six counties in the top 20 U.S. counties with the most records produced.
  • #2 – Illinois.
  • #3 – Iowa.
  • #4 – Minnesota.
  • #5 – Ohio.
  • #6 – Kentucky.
  • #7 – Missouri.
  • #8 – Kansas.
You might be interested:  Question: How To Skull Mount Whitetail Deer?

How old is an 8 point buck?

Nearly all bucks with superior genetics and adequate nutrition have eight or more points when 2 years old. Bucks with inferior antler genetics may never have more than seven points, even when mature.

What is a good Boone and Crockett score?

For Boone and Crockett the minimum scoring points for whitetail deer is 160 inches. For Pope and Young the minimum for whitetail deer is 125 inches. There are also minimums for non-typical antlers. In some states the typical whitetail bucks are well…

How do you calculate buck score?

The rule is to take 100 and add in the total of the tine lengths. This 100-inch figure includes inside spread, main beam length and mass measurements. As you can see, this quickly simplifies scoring a deer on the hoof. If he has three points up and they are 10, 8 and 6 inches, this total 24 inches.

What’s a 10 point buck?

A buck with two standing normal points per side is an 8-pointer, one with three standing points is a 10-pointer, and so on.

How is antler score calculated?

How to Score a Buck—the Right Way

  1. Use a steel tape to measure from the inside of one beam to the inside of the other.
  2. For tine length, stretch masking tape along the top edge of the beam, and then measure from the top of the tape to the tip of the antler.
  3. Take four circumference measurements per side with a steel tape.

Leave a Reply

Your email address will not be published. Required fields are marked *